ADuC7128BCPZ126-RL: Precision Analog Microcontroller ARM7TDMI® MCU with 12-Bit ADC and DDS DAC
The ADuC7128/ADuC7129 are fully integrated, 1 MSPS, 12-bit data acquisition systems incorporating a high performance, multi-channel analog-to-digital converter (ADC), DDS with line driver, 16-/32-bit MCU, and Flash/EE memory on a single chip.
The ADC consists of up to 14 single-ended inputs. The ADC can operate in single-ended or differential input modes. The ADC input voltage is 0 to VREF. Low drift band gap reference, temperature sensor, and voltage comparator complete the ADC peripheral set.
The ADuC7128/ADuC7129 integrate a differential line driver output. This line driver transmits a sine wave whose values are calculated by an on-chip DDS or a voltage output determined by the DACDAT MMR.
The devices operate from an on-chip oscillator and PLL, generating an internal high frequency clock of 41.78 MHz. This clock is routed through a programmable clock divider from which the MCU core clock operating frequency is generated.
The microcontroller core is an ARM7TDMI®, 16-/32-bit reduced instruction set computer (RISC), offering up to 41 MIPS peak performance. There are 126 kB of nonvolatile Flash/EE provided on-chip, as well as 8 kB of SRAM. The ARM7TDMI core views all memory and registers as a single linear array.
On-chip factory firmware supports in-circuit serial download via the UART serial interface port, and nonintrusive emulation is also supported via the JTAG interface. These features are incorporated into a low cost QuickStart™ development system supporting this MicroConverter® family.
The parts operate from 3.0 V to 3.6 V and are specified over an industrial temperature range of −40°C to +125°C. When operating at 41.78 MHz, the power dissipation is 135 mW. The line driver output, if enabled, consumes an additional 30 mW.
ADuC7128BCPZ126-RL 特点
Analog I/O- Multi-Channel, 12-bit, 1MSPS ADC
- Up to 14 analog-to-digital converter (ADC) channels
- Fully differential and single-ended modes
- 0 to VREF Analog Input Range - 10-bit digital-to-analog converter (DAC)
- 32-bit 21 MHz direct digital synthesis (DDS)
- Current-to-Voltage (I/V) Conversion
- Integrated second-order low-pass filter (LPF)
- DDS Input to DAC
- 100 Ω line driver - On-Chip Voltage Reference
- On-Chip Temperature Sensor (±3°C)
- Voltage Comparator
- ARM7TDMI Core, 16/32-bit RISC architecture
- JTAG Port supports code download and debug
- External Watch crystal/ Clock Source
- 41.78 MHz PLL with 8 way Programmable Divider
- Optional Trimmed On-Chip Oscillator
- 126 kB Flash/EE memory, 8 kB SRAM
- In-Circuit Download, JTAG based Debug
- Software triggered in-circuit re-programmability
- 2 x UART, 2 x I²C® and SPI Serial I/O
- Up to 40-pin GPIO port
- 5 X General Purpose Timers
- Wake-up and watchdog timers (WDT)
- Power Supply Monitor
- 16-bit PWM generator
- Quadrature Encoder
- Programmable logic array (PLA)
- Specified for 3V operation
- Active Mode:
11 mA (@ 5.22 MHz)
45 mA (@ 41.78 MHz)
- 64-lead 9 mm × 9 mm LFCSP package, −40°C to 125°C
- 64-lead LQFP, −40°C to +125°C
- 80-lead LQFP, −40°C to +125°C
- Low-Cost QuickStart Development System
- Full Third-Party Support
ADuC7128BCPZ126-RL 功能框图
| 产品型号 | 产品状态 | 封装 | 引脚 | 温度范围 |
|---|---|---|---|---|
| ADuC7128BCPZ126 | 量产 | 64 ld LFCSP (9x9mm, 4.70mm exposed pad) | 64 | 工业 |
| ADuC7128BCPZ126-RL | 量产 | 64 ld LFCSP (9x9mm, 4.70mm exposed pad) | 64 | 工业 |
| ADuC7128BSTZ126 | 量产 | 64 ld LQFP (10x10mm) | 64 | 工业 |
| ADuC7128BSTZ126-RL | 量产 | 64 ld LQFP (10x10mm) | 64 | 工业 |
| EVAL-ADuC7128QSPZ | 量产 | 评估板 | - | 待定 |
