AT45DB081D 8Mbit,SPI接口DateFlash存储器

Density 8M
I/O Pins 8
Interface Type SPI, RapidS
Page Size (Bytes) 264
Vcc (V) 2.5, 2.7
Pb-Free Packages SOIC (150mil)8
SOIC (208mil)8
MLF (VDFN) 8

8M bit, 2.5 or 2.7-Volt Only Serial-Interface Flash

The AT45DB081D is a 2.5V or 2.7V, serial-interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications. The AT45DB081D supports RapidS serial interface for applications requiring very high speed operations. RapidS serial interface is SPI compatible for frequencies up to 66 MHz. Its 8,650,752 bits of memory are organized as 4,096 pages of 256 bytes or 264 bytes each. In addition to the main memory, the AT45DB081D also contains two SRAM buffers of 256/264 bytes each. The buffers allow the receiving of data while a page in the main Memory is being reprogrammed, as well as writing a continuous data stream. EEPROM emulation (bit or byte alterability) is easily handled with a selfcontained three step read-modify-write operation. Unlike conventional Flash memoriesthat are accessed randomly with multiple address lines and a parallel interface,the DataFlash uses a RapidS serial interface to sequentially access its data. The simple sequential access dramatically reduces active pin count, facilitates hardware layout, increases system reliability, minimizes switching noise, and reduces package size. The device is optimized for use in many commercial and industrial applications where high-density, low-pin count, low-voltage and low-power are essential. To allow for simple in-system reprogrammability, the AT45DB081D does not require high input voltages for programming. The device operates from a single power supply, 2.5V to 3.6V or 2.7V to 3.6V, for both the program and read operations. The AT45DB081D is enabled through the chip select pin (CS) and accessed via a three-wire interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK). All programming and erase cycles are self-timed.

AT45DB081D 特性
AT45DB081D 订购型号
Ordering Code Package Lead Finish Operating Voltage Max. Freq.
(MHz)
Operation Range
AT45DB081D-MU
AT45DB081D-MU-SL954
AT45DB081D-MU-SL955
8M1-A Matte Sn 2.7V to 3.6V 66 Industrial (-40°C to +85°C)
AT45DB081D-SSU
AT45DB081D-SSU-SL954
AT45DB081D-SSU-SL955
8S1 Matte Sn 2.7V to 3.6V 66 Industrial (-40°C to +85°C)
AT45DB081D-SU
AT45DB081D-SU-SL954
AT45DB081D-SU-SL955
8S2 Matte Sn 2.7V to 3.6V 66 Industrial (-40°C to +85°C)
AT45DB081D-MU-2.5
AT45DB081D-SSU-2.5
AT45DB081D-SU-2.5
8M1-A
8S1
8S2
Matte Sn 25V to 3.6V 50 Industrial (-40°C to +85°C)
AT45DB081D 应用技术支持与电子电路设计开发资源下载
  1. ATMEL 爱特梅尔Flash 存储器AT45DB081D 数据手册DataSheet 下载. PDF(PDF 文件格式完整版)
  2. 串行Flash 产品选型指南(Excel 文档格式)
  3. ATMEL 爱特梅尔公司全线产品目录. pdf
  4. Programmer Support for Serial Flash Devices. pdf (Other, 8 pages, revision C, updated 4/08)
  5. MicroLeadFrame Packages Pad Landing Recommendations (15 pages, revision B, updated 09/06). pdf
    This application note provides PCB designers with a set of guidelines for successful board mounting of Atmel's DataFlash memories housed in the MicroLeadFrame (MLF) package.
  6. AN-4: Using Atmel's DataFlash (30 pages, updated 11/02) . pdf
    Atmel's DataFlash is a new Flash family designed specifically for data storage applications. This Application Note describes this family.
  7. DataFlash Binary Page Size (2 pages, revision A, updated 5/08) . pdf
    Factory Configured DataFlash Binary Page Size options