1. 嵌入式微控制器和微处理器
   8位单片机
   16 位单片机
   32位ARM核微处理器
   AVR 单片机
   DSP 数字信号处理
   其他专用单片机
2. 存储器
   非易失性存储器NVRAM
   同步动态存储器SDRAM
   EEPROM 存储器
   Flash 存储器
   其他
3. 系统管理器件
   监控电路（电压监控器）
   低功耗复位器
4. Interface 接口器件
   RS-232接口
   RS-485/422接口
   CAN接口
   USB 接口
   LVDS与RF接口
   其他接口
5. 数据转换器
   模数转换器
   数模转换器
   音频与触摸屏控制器
6. 电源管理器件
   标准线性电源
   低压差稳压器
   DC/DC转换器
   AC/DC转换器
   电压基准
   电池管理
   PWM控制器
   电源模块与功率器件
   其它
7. 时钟管理 定时器 计数器
8. 数字电位器 DCP
9. 开关器件
10. 传感器
11. 可编程逻辑器件
    FPGA 现场可编程逻辑
    CPLD 复杂可编程逻辑器件
    其它 可编程系统器件
12. 逻辑电路
13. 其他

首页＞ATMEL 爱特梅尔＞DataFlash存储器＞AT45DB642D

ATMEL 爱特梅尔串行FLASH 存储器AT45DB642D AT45DB642D 概述 The AT45DB642D is a 2.7-volt, dual-interface sequential access Flash memory ideally suited for
a wide variety of digital voice-, image-, program code- and data-storage applications. The
AT45DB642D supports RapidS serial interface and Rapid8 8-bit interface. RapidS serial interface
is SPI compatible for frequencies up to 66 MHz. The dual-interface allows a dedicated
serial interface to be connected to a DSP and a dedicated 8-bit interface to be connected to a
microcontroller or vice versa. However, the use of either interface is purely optional. Its
69,206,016 bits of memory are organized as 8,192 pages of 1,024 bytes (binary page size) or
1,056 bytes (standard DataFlash page size) each. In addition to the main memory, the
AT45DB642D also contains two SRAM buffers of 1,024 (binary buffer size) bytes/1,056 bytes
(standard DataFlash buffer size) each. The buffers allow receiving of data while a page in the
main Memory is being reprogrammed, as well as writing a continuous data stream. EEPROM
emulation (bit or byte alterability) is easily handled with a self-contained three step read-modifywrite
operation. Unlike conventional Flash memories that are accessed randomly with multiple
address lines and a parallel interface, the DataFlash uses either a RapidS serial interface or a
8-bit Rapid8 interface to sequentially access its data. The simple sequential access dramatically
reduces active pin count, facilitates hardware layout, increases system reliability, minimizes
switching noise, and reduces package size. The device is optimized for use in many commercial
and industrial applications where high-density, low-pin count, low-voltage and low-power are
essential.
To allow for simple in-system reprogrammability, the AT45DB642D does not require high input
voltages for programming. The device operates from a single power supply, 2.7V to 3.6V, for
both the program and read operations. The AT45DB642D is enabled through the chip select pin
(CS) and accessed via a three-wire interface consisting of the Serial Input (SI), Serial Output
(SO), and the Serial Clock (SCK), or an 8-bit interface consisting of the input/output pins (I/O7 -
I/O0) and the clock pin (CLK).
All programming and erase cycles are self-timed. AT45DB642D 特性

• Single 2.7V - 3.6V Supply
  • Dual-interface Architecture
  – RapidS™ Serial Interface: 66 MHz Maximum Clock Frequency
  SPI Compatible Modes 0 and 3
  – Rapid8™ 8-bit Interface: 50 MHz Maximum Clock Frequency
  • User Configurable Page Size
  – 1024 Bytes per Page
  – 1056 Bytes per Page
  – Page Size Can Be Factory Pre-configured for 1024 Bytes
  • Page Program Operation
  – Intelligent Programming Operation
  – 8192 Pages (1024/1056 Bytes/Page) Main Memory
  • Flexible Erase Options
  – Page Erase (1 Kbyte)
  – Block Erase (8 Kbytes)
  – Sector Erase (256 Kbytes)
  – Chip Erase (64 Mbits)
  • Two SRAM Data Buffers (1024/1056 Bytes)
  – Allows Receiving of Data while Reprogramming the Flash Array
  • Continuous Read Capability through Entire Array
  – Ideal for Code Shadowing Applications
  • Low-power Dissipation
  – 10 mA Active Read Current Typical – Serial Interface
  – 10 mA Active Read Current Typical – 8-bit Interface
  – 25 μA Standby Current Typical
  – 9 μA Deep Power Down Typical
  • Hardware and Software Data Protection Features
  – Individual Sector
  • Permanent Sector Lockdown for Secure Code and Data Storage
  – Individual Sector
  • Security: 128-byte Security Register
  – 64-byte User Programmable Space
  – Unique 64-byte Device Identifier
  • JEDEC Standard Manufacturer and Device ID Read
  • 100,000 Program/Erase Cycles Per Page Minimum
  • Data Retention – 20 Years
  • Green (Pb/Halide-free/RoHS Compliant) Packaging Options
  • Temperature Range
  – Industrial: -40° C to +85°C

AT45DB642D 订购型号