MC9S12HZ256VAL | BDTIC 半导体事业部代理Freescale飞思卡尔16位微控制器MC9S12HZ256，MC9S12HZ256CAL,MC9S12HZ256VAL,MC9S12HZ256CPV,MC9S12HZ256MPV,MC9S12HZ256VPV,MC9S12HZ256VPVR2

The MC9S12HZ256CPV microcontroller units (MCU) are 16-bit devices composed of standard on-chip peripherals including a 16-bit central processing unit (HCS12 CPU), up to 256K bytes of Flash EEPROM or ROM, up to 12K bytes of RAM, 2K bytes of EEPROM, two asynchronous serial communications interfaces (SCI), a serial peripheral interface (SPI), an IIC-bus interface (IIC), an 8-channel 16-bit timer (TIM), a 16-channel, 10-bit analog-to-digital converter (ATD), a six-channel pulse width modulator (PWM), and two CAN 2.0 A, B software compatible modules (MSCAN). In addition, they feature a 32x4 liquid crystal display (LCD) controller/driver, a pulse width modulator motor controller (MC) consisting of 16 high current outputs suited to drive up to four stepper motors, and four stepper stall detectors (SSD) to simultaneously calibrate the pointer position of each motor. System resource mapping, clock generation,interrupt control, and external bus interfacing are managed by the HCS12 Core. The MC9S12HZ256CPV have full 16-bit data paths throughout. The inclusion of a PLL circuit allows power consumption and performance to be adjusted to suit operational requirements. In addition to the I/O ports available in each module, 8 general-purpose I/O pins are available with interrupt and wake-up capability from stop or wait mode.

MC9S12HZ256CPV 特性

HCS12 core
– 16-bit HCS12 CPU
Upward compatible with M68HC11
Interrupt stacking and programmer’s
16-bit ALU
Instruction queue
Enhanced indexed addressing
– MEBI (multiplexed external bus interface)
– MMC (module mapping control)
– INT (interrupt control)
– DBG (debugger and breakpoints)
– BDM (background debug mode)• Memory
– 256K, 128K, 64K, 32K Flash EEPROM or ROM
– 2K, 1K byte EEPROM
– 12K, 6K, 4K, 2K byte RAM
CRG (low current oscillator, PLL, reset, clocks, COP watchdog, real time interrupt, clock monitor)
Analog-to-digital converter
– 16 channels, 10-bit resolution
– External conversion trigger capability
Two 1-Mbps, CAN 2.0 A, B software compatible modules
– Five receive and three transmit buffers
– Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit or 8 x 8 bit
– Four separate interrupt channels for Rx, Tx, error and wake-up
– Low-pass filter wake-up function
– Loop-back for self test operation
Timer
– 16-bit main counter with 7-bit prescaler
– 8 programmable input capture or output compare channels
– Two 8-bit or one 16-bit pulse accumulators
6 PWM channels
– Programmable period and duty cycle
– 8-bit 6-channel or 16-bit 3-channel
– Separate control for each pulse width and duty cycle
– Center-aligned or left-aligned outputs
– Programmable clock select logic with a wide range of frequencies
– Fast emergency shutdown input
Serial interfaces
– Two asynchronous serial communications interfaces (SCI)
– Synchronous serial peripheral interface (SPI)
– Inter-integrated circuit interface (IIC)
Liquid crystal display (LCD) driver with variable input voltage
– Configurable for up to 32 frontplanes and 4 backplanes or general-purpose input or output
– 5 modes of operation allow for different display sizes to meet application requirements
– Unused frontplane and backplane pins can be used as general-purpose I/O
PWM motor controller (MC) with 16 high current drivers
– Each PWM channel switchable between two drivers in an H-bridge configuration
– Left, right and center aligned outputs
– Support for sine and cosine drive
– Dithering
– Output slew rate control
Four stepper stall detectors (SSD)
– Full step control during return to zero
– Voltage detector and integrator / sigma delta converter circuit
– 16-bit accumulator register
– 16-bit modulus down counter
112-pin LQFP and 80-pin QFP packages
– 85 I/O lines with 5-V input and drive capability
– 5-V A/D converter inputs
– 8 key wake up interrupts with digital filtering and programmable rising/falling edge trigger
Operation at 50 MHz equivalent to 25-MHz bus speed
• Development support
– Single-wire background debug™ mode (BDM)
– Debugger and on-chip hardware breakpoints

MC9S12HZ256CPV 产品区别

对比	MC9S12HZ256	MC9S12HZ128	MC9S12HZ64	MC9S12HN64
FLASH	256K	128K	64K	64K
RAM	12K	6K	4K	4K
EEPROM	2K	2K	1K	1K
Serial Interfaces (up to)	2 CAN 2 SCI 1 SPI 1 IIC	2 CAN 2 SCI 1 SPI 1 IIC	1 CAN 1 SCI 1 SPI	1 SCI 1 SPI
LCD (up to)	32x4	32x4	24x4	24x4
Package	112 LQFP	112 LQFP	80 QFP 112 LQFP	80 QFP 112 LQFP

MC9S12HZ256 选型

Part Number	Package Description & Diagram	Tape and Reel	Qualification Tier	Package Peak Temperature (ºC)	Compliance Flags RoHS	Internal Flash (Byte)	Internal RAM (Byte)	EEPROM (Byte)	Core Operating Frequency (Max) (MHz)	Bus Frequency (Max) (MHz)	Supply Voltage (Min) (V)	Supply Voltage (Max) (V)	Timers Number of Timers	Timers Channels	Timers Size (bit)	Serial Interface Number of Interfaces	Serial Interface Type	CAN	A/D Converter Bits (bit)	A/D Converter Channels	I/O Pins	Ambient Operating Temperature (Ta) (Min) (oC)	Ambient Operating Temperature (Ta) (Max) (oC)
MC9S12HZ256CAL	LQFP 112 20201.4P0.65	N	COMMERCIAL, INDUSTRIAL, AUTOMOTIVE	260	环保无铅	256000	12000	2000	50	25	4.5	5.5	1	8	16	2 1 1 2	SCI SPI I2C CAN	CAN 2.0 A/B	10	16	85	-40	85
MC9S12HZ256VAL	LQFP 112 20201.4P0.65	N	COMMERCIAL, INDUSTRIAL, AUTOMOTIVE	260	环保无铅	256000	12000	2000	50	25	4.5	5.5	1	8	16	2 1 1 2	SCI SPI I2C CAN	CAN 2.0 A/B	10	16	85	-40	105
MC9S12HZ256CPV	LQFP 112 20201.4P0.65	N	COMMERCIAL, INDUSTRIAL, AUTOMOTIVE	220	No	262144	12288	2048	-	25	-	-	-	-	-	-	-	-	-	-	85	-40	85
MC9S12HZ256MPV	LQFP 112 20201.4P0.65	N	COMMERCIAL, INDUSTRIAL, AUTOMOTIVE	220	No	262144	12288	2048	-	25	-	-	-	-	-	-	-	-	-	-	85	-40	125
MC9S12HZ256VPV	LQFP 112 20201.4P0.65	N	COMMERCIAL, INDUSTRIAL, AUTOMOTIVE	220	No	262144	12288	2048	-	25	-	-	-	-	-	-	-	-	-	-	85	-40	105
MC9S12HZ256VPVR2	LQFP 112 20201.4P0.65	Y	COMMERCIAL, INDUSTRIAL, AUTOMOTIVE	220	No	262144	12288	2048	-	25	-	-	-	-	-	-	-	-	-	-	85	-40	105

MC9S12HZ256CPV 技术支持

站点首页库存调剂设为主页关于我们人才招聘网站导航隐私保护友情链接 IC 专卖店联系我们