• 简体中文
• English

PCA9509: Level translating I²C-bus/SMBus repeater

The PCA9509 is a level translating I²C-bus/SMBus repeater that enables processor low voltage 2-wire serial bus to interface with standard I²C-bus or SMBus I/O. While retaining all the operating modes and features of the I²C-bus system during the level shifts, it also permits extension of the I²C-bus by providing bidirectional buffering for both the data (SDA) and the clock (SCL) lines, thus enabling the I²C-bus or SMBus maximum capacitance of 400 pF on the higher voltage side. Port A allows a voltage range from 1.35 V to VCC(B) ‑ 1.0 V and requires no external pull-up resistors due to the internal current source. Port B allows a voltage range from 3.0 V to 5.5 V and is overvoltage tolerant. Both port A and port B SDA and SCL pins are high-impedance when the PCA9509 is unpowered.

For applications where Port A VCC(A) is less than 1.35 V or Port B VCC(B) is less than 3.0 V, use drop-in replacement PCA9509A.

The bus port B drivers are compliant with SMBus I/O levels, while port A uses a current sensing mechanism to detect the input or output LOW signal which prevents bus lock-up. Port A uses a 1 mA current source for pull-up and a 200 Ω pull-down driver. This results in a LOW on the port A accommodating smaller voltage swings. The output pull-down on the port A internal buffer LOW is set for approximately 0.2 V, while the input threshold of the internal buffer is set about 50 mV lower than that of the output voltage LOW. When the port A I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition from occurring. The output pull-down on the port B drives a hard LOW and the input level is set at 0.3 of SMBus or I²C-bus voltage level which enables port B to connect to any other I²C-bus devices or buffer.

The PCA9509 drivers are not enabled unless VCC(A) is above 0.8 V and VCC(B) is above 2.5 V. The enable (EN) pin can also be used to turn on and turn off the drivers under system control. Caution should be observed to change only the state of the EN pin when the bus is idle.

PCA9509: Product Block Diagram

Outline 3d SOT902-1

0 Hz to 400 kHz clock frequency

Remark: The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater.

Data Sheets (1)

Application Notes (3)

Users Guides (4)

Brochures (2)

Package Information (3)

Packing (3)

Supporting Information (4)

Ordering Information

Package Information

Product ID	Package Description	Outline Version	Reflow/Wave Soldering	Packing	Product Status	Part NumberOrdering code(12NC)	Marking	Chemical Content	RoHS / Pb Free / RHF	LeadFree Conversion Date	EFR	IFR(FIT)	MTBF(hour)	MSL	MSL LF
PCA9509GM		SOT902-1		Reel 7" Q3/T4, Reverse	Active	PCA9509GM,125 (9352 841 39125)	Standard Marking	PCA9509GM		Always Pb-free	0.0	2.0	5E8	1	1
PCA9509D		SOT96-1	SO-SOJ-REFLOW SO-SOJ-WAVE SO-SOJ-REFLOW SO-SOJ-WAVE	Reel 13" Q1/T1	Active	PCA9509D,118 (9352 822 27118)	PCA9509	PCA9509D		Always Pb-free	0.0	2.0	5E8	1	1
				Bulk Pack	Active	PCA9509D,112 (9352 822 27112)	PCA9509	PCA9509D		Always Pb-free	0.0	2.0	5E8	1	1
PCA9509DP		SOT505-1	Reflow_Soldering_Profile	Reel 13" Q1/T1	Active	PCA9509DP,118 (9352 822 26118)	9509	PCA9509DP		Always Pb-free	0.0	2.0	5E8	1	1
PCA9509DP/DG		SOT505-1	Reflow_Soldering_Profile	Reel 13" Q1/T1	Withdrawn	PCA9509DP/DG,118 (9352 934 08118)	9509			Always Pb-free	0.0	2.0	5E8	1	1