UJA1078ATW: High-speed CAN/dual LIN core system basis chip

The UJA1078A core System Basis Chip (SBC) replaces the basic discrete components commonly found in Electronic Control Units (ECU) with a high-speed Controller Area Network (CAN) and two Local Interconnect Network (LIN) interfaces.

The UJA1078A supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface and the LIN interfaces as local sub-busses.

The core SBC contains the following integrated devices:

In addition to the advantages gained from integrating these common ECU functions in a single package, the core SBC offers an intelligent combination of system-specific functions such as:

The UJA1078A is designed to be used in combination with a microcontroller that incorporates a CAN controller. The SBC ensures that the microcontroller always starts up in a controlled manner.

sot549-1_3d
2.1 General
  • Contains a full set of CAN and LIN ECU functions: CAN transceiver and two LIN transceivers Scalable 3.3 V or 5 V voltage regulator delivering up to 250 mA for a microcontroller and peripheral circuitry; an external PNP transistor can be connected for better heat distribution over the PCB Separate voltage regulator for the CAN transceiver (5 V) Watchdog with Window and Timeout modes and on-chip oscillator Serial Peripheral Interface (SPI) for communicating with the microcontroller ECU power management system
  • Designed for automotive applications: Enhanced ElectroMagnetic Compatibility (EMC) performance ±8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) on the CAN/LIN bus pins and the wake-up pins ±6 kV ElectroStatic Discharge protection IEC 61000-4-2 on the CAN/LIN bus pins and the wake-up pins ±58 V short-circuit proof CAN/LIN bus pins Battery and CAN/LIN bus pins are protected against transients in accordance with ISO 7637-3
  • Supports remote flash programming via the CAN bus
  • Small 6.1 mm × 11 mm HTSSOP32 package with low thermal resistance
  • Pb-free; Restriction of Hazardous Substances Directive (RoHS) and dark green compliant
CAN transceiver
  • ISO 11898-2 and ISO 11898-5 compliant high-speed CAN transceiver
  • Dedicated low dropout voltage regulator for the CAN bus: Independent of the microcontroller supply Significantly improves EMC performance
  • Bus connections are truly floating when power is off
  • SPLIT output pin for stabilizing the recessive bus level
LIN transceivers
  • 2 × LIN 2.1 compliant LIN transceivers
  • Compliant with SAE J2602
  • Downward compatible with LIN 2.0 and LIN 1.3
  • Low slope mode for optimized EMC performance
  • Integrated LIN termination diode at pin DLIN
Power management
  • Wake-up via CAN, LIN or local wake-up pins with wake-up source detection
  • 2 wake-up pins: WAKE1 and WAKE2 inputs can be switched off to reduce current flow Output signal (WBIAS) to bias the wake-up pins, selectable sampling time of 16 ms or 64 ms
  • Standby mode with very low standby current and full wake-up capability; V1 active to maintain supply to the microcontroller
  • Sleep mode with very low sleep current and full wake-up capability
Control and diagnostic features
  • Safe and predictable behavior under all conditions
  • Programmable watchdog with independent clock source: Window, Timeout (with optional cyclic wake-up) and Off modes supported (with automatic re-enable in the event of an interrupt)
  • 16-bit Serial Peripheral Interface (SPI) for configuration, control and diagnosis
  • Global enable output for controlling safety-critical hardware
  • Limp home output (LIMP) for activating application-specific ‘limp home’ hardware in the event of a serious system malfunction
  • Overtemperature shutdown
  • Interrupt output pin; interrupts can be individually configured to signal V1/V2 undervoltage, CAN/LIN/local wake-up and cyclic and power-on interrupt events
  • Bidirectional reset pin with variable power-on reset length to support a variety of microcontrollers
  • Software-initiated system reset
Voltage regulators
  • Main voltage regulator V1: Scalable voltage regulator for the microcontroller, its peripherals and additional external transceivers ±2 % accuracy 3.3 V and 5 V versions available Delivers up to 250 mA and can be combined with an external PNP transistor for better heat distribution over the PCB Selectable current threshold at which the external PNP transistor starts to deliver current Undervoltage warning at 90 % of nominal output voltage and undervoltage reset at 90 % or 70 % of nominal output voltage Can operate at VBAT voltages down to 4.5 V (e.g. during cranking), in accordance with ISO 7637 pulse 4/4b and ISO16750-2 Stable output under all conditions
  • Voltage regulator V2 for CAN transceiver: Dedicated voltage regulator for on-chip high-speed CAN transceiver Undervoltage warning at 90 % of nominal output voltage Can be switched off; CAN transceiver can be supplied by V1 or by an external voltage regulator Can operate at VBAT voltages down to 5.5 V (e.g. during cranking) in accordance with ISO 7637, pulse 4 Stable output under all conditions
Data Sheets (2)
Name/DescriptionModified Date
UJA1078A,高速CAN/ デュアルLIN... (REV 2.0) PDF (600.0 kB) UJA1078A_JP_116 Sep 2016
High-speed CAN/dual LIN core system basis chip (REV 2.0) PDF (381.0 kB) UJA1078A28 Jan 2011
Package Information (1)
Name/DescriptionModified Date
plastic thermal enhanced thin shrink small outline package; 32 leads; body width 6.1 mm; lead pitch 0.65 mm; exposed die... (REV 1.0) PDF (380.0 kB) SOT549-108 Feb 2016
Ordering Information
ProductStatusProduct categoryCategorySupported standardsPackage nameLow power modesPackage versionSupply voltage [min] (V)Supply voltage [max] (V)Data rate [min] (kb/s)Data rate [max] (kb/s)CAN channelsLIN channelsVoltage on bus pins [min] (V)Voltage on bus pins [max] (V)FlexRay ChannelsVESD IEC61000-4-2 (kV)VESD HBM on bus pins (+/- kV)VIO option availableApplicationRecommended VersionTvj [max] (°C)Rth(j-a) (K/W)SPLIT pinUnder-voltage detectionTX Dominant Time outOver-temperature detectionINH / Wake PinMin High Input Levels (V)No of pins
UJA1078ATW/5V0ActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/3V3/WD/1ActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/5V0/1ActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/5V0/WDActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/3V3ActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/3V3/1ActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/3V3/WDActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
UJA1078ATW/5V0/WD/1ActiveSBC; High-Speed CAN; LIN TransceiverISO-11898-2; ISO-11898-5; LIN-2.1; SAE-J2602HTSSOP32Standby Mode; Sleep Mode4.54015100012-585868NoYes250mA
Package Information
Product IDPackage DescriptionOutline VersionReflow/Wave SolderingPackingProduct StatusPart NumberOrdering code(12NC)MarkingChemical ContentRoHS / Pb Free / RHFLeadFree Conversion DateMSLMSL LF
UJA1078ATW/3V3SOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/3V3,118 (9352 924 21118)Standard MarkingUJA1078ATW/3V3Always Pb-free11
UJA1078ATW/3V3/1SOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/3V3/1J (9353 027 06118)Standard MarkingUJA1078ATW/3V3/1Always Pb-free11
UJA1078ATW/3V3/WDSOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/3V3WD,1 (9352 924 23118)Standard MarkingUJA1078ATW/3V3/WDAlways Pb-free11
UJA1078ATW/3V3/WD/1SOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/3V3/WDJ (9353 027 08118)Standard MarkingUJA1078ATW/3V3/WD/1Always Pb-free11
UJA1078ATW/5V0SOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/5V0,118 (9352 924 19118)Standard MarkingUJA1078ATW/5V0Always Pb-free11
UJA1078ATW/5V0/1SOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/5V0/1J (9353 027 05118)Standard MarkingUJA1078ATW/5V0/1Always Pb-free11
UJA1078ATW/5V0/WDSOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/5V0WD,1 (9352 924 22118)Standard MarkingUJA1078ATW/5V0/WDAlways Pb-free11
UJA1078ATW/5V0/WD/1SOT549-1Reel 13" Q1/T1ActiveUJA1078ATW/5V0/WDJ (9353 027 07118)Standard MarkingUJA1078ATW/5V0/WD/1Always Pb-free11
High-speed CAN/dual LIN core system basis chip uja1078atw
High-speed CAN/dual LIN core system basis chip can_lin_flexray_transceivers
Footprint for reflow soldering SOT549-1 UJA1079ATW
plastic thermal enhanced thin shrink small outline package; 32 leads; body width 6.1 mm; lead pitch 0.65 mm; exposed die pad UJA1079ATW