USB3370

Microchip's USB3370 is a family of Hi-Speed USB 2.0 Transceivers that provide a physical layer (PHY) solution well-suited for portable electronic devices. Both commercial and industrial temperature applications are supported.

Several advanced features make the USB3370 the transceiver of choice by reducing both eBOM part count and printed circuit board (PCB) area. Outstanding ESD robustness eliminates the need for external ESD protection devices in typical applications. The internal Over-Voltage Protection circuit (OVP) protects the USB3370 from voltages up to 30V on the VBUS pin. By using a reference clock from the Link, the USB3370 removes the cost of a dedicated crystal reference from the design. The USB3370 includes integrated 3.3V and 1.8V regulators, making it possible to operate the device from a single power supply.

The USB3370 is optimized for use in portable applications where a low operating current and standby currents are essential. The USB3370 operates from a single supply and includes integrated regulators for its supplies. The USB3370 also supports the USB Link Power Management protocol (LPM) to further reduce USB operating currents.

The USB3370 also includes family is enabled with Microchip's RapidCharge AnywhereTM which supports USB-IF Battery Charging 1.1 for any portable device. RapidCharge AnywhereTM provides three times the charging current through a USB port over traditional solutions which translate up to 1.5Amps via compatible USB host or dedicated charger. In addition, this provides a complete USB charging ecosystem between device and host ports such as Dedicated Charging Port (DCP), Charging (CDP) and Standard (SDP) Downstream Ports. Section 5.9 describes this is further detail.

The USB3370 meets all of the electrical requirements for a Hi-Speed USB Host, Device, or an On-the- Go (OTG) transceiver. In addition to the supporting USB signaling, the USB3370 also provides USB UART mode.

USB3370 uses the industry standard UTMI+ Low Pin Interface (ULPI) to connect the USB transceiver to the Link. ULPI uses a method of in-band signaling and status byte transfers between the Link and PHY to facilitate a USB session with only twelve pins.

The USB3370 uses Microchip’s “wrapper-less” technology to implement the ULPI interface. This “wrapperless” technology allows the PHY to achieve a low latency transmit and receive time. Microchip’s low latency transceiver allows an existing UTMI Link to be reused by adding a UTMI to ULPI bridge. By adding a bridge to the ASIC the existing and proven UTMI Link IP can be reused.

产品特性
  • USB-IF Battery Charging 1.1 Specification Compliant
  • Link Power Management (LPM) Specification Compliant
  • Integrated ESD protection circuits Up to ±25kV IEC Air Discharge without external devices
  • Up to ±25kV IEC Air Discharge without external devices
  • Over-Voltage Protection circuit (OVP) protects the VBUS pin from continuous DC voltages up to 30V
  • Microchip RapidCharge Anywhere™ Provides: 3-times the charging current through a USB port over traditional solutions USB-IF Battery Charging 1.1 compliance to any portable device Charging current up to 1.5Amps via compatible USB host or dedicated charger Dedicated Charging Port (DCP), Charging (CDP) & Standard (SDP) Downstream Port support
  • 3-times the charging current through a USB port over traditional solutions
  • USB-IF Battery Charging 1.1 compliance to any portable device
  • Charging current up to 1.5Amps via compatible USB host or dedicated charger
  • Dedicated Charging Port (DCP), Charging (CDP) & Standard (SDP) Downstream Port support
  • flexPWR® Technology Extremely low current design ideal for battery powered applications "Sleep" mode tri-states all ULPI pins and places the part in a low current state 1.8V to 3.3V IO Voltage
  • Extremely low current design ideal for battery powered applications
  • "Sleep" mode tri-states all ULPI pins and places the part in a low current state
  • 1.8V to 3.3V IO Voltage
  • Single Power Supply Operation Integrated 1.8V regulator Integrated 3.3V regulator 100mV dropout voltage
  • Integrated 1.8V regulator
  • Integrated 3.3V regulator
  • 100mV dropout voltage
  • PHYBoost Programmable USB transceiver drive strength for recovering signal integrity
  • Programmable USB transceiver drive strength for recovering signal integrity
  • VariSense™ Programmable USB receiver sensitivity
  • Programmable USB receiver sensitivity
  • "Wrapper-less" design for optimal timing performance and design ease
  • Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI bridge
  • External Reference Clock operation available ULPI Clock Input Mode (60MHz sourced by Link) 0 to 3.6V input drive tolerant Able to accept "noisy" clock sources as reference to internal, low-jitter PLL Crystal support available
  • ULPI Clock Input Mode (60MHz sourced by Link)
  • 0 to 3.6V input drive tolerant
  • Able to accept "noisy" clock sources as reference to internal, low-jitter PLL
  • Crystal support available
  • Smart detection circuits allow identification of USB charger, headset, or data cable insertion
  • Includes full support for the optional On-The-Go OTG) protocol detailed in the On-The-Go Supplement Revision 2.0 specification
  • Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
  • UART mode for non-USB serial data transfers
  • Internal 5V cable short-circuit protection of ID, DP and DM lines to VBUS or ground
  • Industrial Operating Temperature -40°C to +85°C
  • 32 pin, QFN RoHS Compliant package (5 x 5x 0.90 mm height)
  • Cell Phones
  • PDAs
  • MP3 Players
  • GPS Personal Navigation
  • Scanners
  • External Hard Drives
  • Digital Still and Video Cameras
  • Portable Media Players
  • Entertainment Devices
  • Printers
  • Set Top Boxes
  • Video Record/Playback Systems
  • IP and Video Phones
  • Gaming Consoles
技术参数
Parameter Name Value Value
Upstream Port ULPI ULPI
Reference Clock Freq 19.2Mhz 19.2Mhz
I/O Voltage (V) 1.8V to 3.3V 1.8V to 3.3V
ULPI Input Clock Mode Yes Yes
Crystal Support Yes Yes
Battery Charger Detection Yes Yes
OTG Yes Yes
Host Based I/F Yes Yes
Temp. Range Min. -40 -40
Temp. Range Max. 85 85
文档资料
USB3370 Enhanced Single Supply Hi-Speed USB ULPI Transceiver v1.0Data Sheets05/22/20151151KB
AN26.21 - USB Device Design ChecklistAppNote08/10/2015386KB
USB3370 Enhanced Single Supply Hi-Speed USB ULPI Transceiver v1.0Product Brief03/18/2014309KB
订购型号
Part NumberLeadsPackage TypeTemp RangePacking1+26+100+1000+5000+
USB3370B-EZK32VQFN-40C to +85CTRAY1.551.291.181.141.12
USB3370B-EZK-TR32VQFN-40C to +85CT/R1.551.291.181.141.12
相类似产品
ProductUpstream PortDownstream PortsI/O Voltage (v)Price5K
USB3250UTMIUSB3.3V
USB3280UTMIUSB3.3V
USB3290UTMIUSB3.3V$1.07
USB3300ULPIUSB3.3V$0.90
USB3310ULPIUSB1.8V$0.90
USB3311ULPIUSB1.8V$0.90
USB3315ULPIUSB1.8V-3.3V$0.90
USB3316ULPIUSB1.8V$0.90
USB3317ULPIUSB1.8V-3.3V$0.90
USB3318ULPIUSB1.8V-3.3V$0.90
USB3319ULPIUSB1.8V$0.90
USB3320ULPIUSB1.8V-3.3V$1.12
USB3321ULPIUSB1.8V
USB3322ULPIUSB1.8V$1.24
USB3326ULPIUSB1.8V$1.24
USB3327ULPIUSB1.8V$1.24
USB3329ULPIUSB1.8V$1.24
USB3330ULPIUSB1.8V$1.35
USB3331ULPIUSB1.8V$1.35
USB3333ULPIUSB1.8V-3.3V$1.35
USB3336ULPIUSB1.8V$1.35
USB3338ULPIUSB1.8V$1.35
USB3340ULPIUSB1.8V-3.3V$1.12
USB3341ULPIUSB1.8V$0.90
USB3343ULPIUSB1.8V-3.3V$0.90
USB3346ULPIUSB1.8V$0.90
USB3347ULPIUSB1.8V$0.90
USB3370ULPIUSB1.8V to 3.3V$1.12
USB3450UTMI+USB3.3V
USB3500UTMI+USB3.3V
器件无铅环保信息
PartNumberDeviceWeightShippingWeightLeadCountPackageTypePackageWidthSolderCompositionJEDECIndicatorRoHSChinaEFUP
USB3370B-EZK-TR0.0636000.13800032VQFN5x5x0.9mmMatte Tine3
USB3370B-EZK0.0636000.73469432VQFN5x5x0.9mmMatte Tine3
USB3370 Enhanced Single Supply Hi-Speed USB ULPI Transceiver v1.0 USB3370
AN26.21 USB3751A-2
USB3370 Enhanced Single Supply Hi-Speed USB ULPI Transceiver v1.0 USB3370