ST25R3910:NFC / HF RFID Reader IC

The ST25R3910 is a high performance 13.56 MHz RFID reader, with two differential, low impedance (1.5 Ohm) antenna drivers.

These drivers are unmatched, allowing the ST25R3910 to deliver up to eight times the output power of a standard HF reader IC using the same power supply voltage, and reducing in half the power consumption at the same output power.

The ST25R3910 can operate already at 2.4 V, with a low power operating mode of 5 mA, making it perfectly suited for portable or battery-powered applications.

For applications where high power is required the ST25R3910 can deliver up to 700 mW, thus avoiding the need for complex external booster circuitry.

The component count and complexity of the design is further reduced through automatic modulation depth adjustment.

The analog front end (AFE) is complemented by a highly integrated data framing engine for both ISO-14443 A and B. This includes data rates up to 848 kbit/s, with all framing and synchronization tasks on board. This enables to build a complete HF RFID reader using only a low end MCU.

The ST25R3910 supports reader to tag and Peer to Peer communication using the NFCIP-1 active communication mode with a 106 kbps data rate. Other standard and custom protocols, such as ISO-15693 or FeliCa™ can be implemented via transparent mode. The ST25R3910 features a SPI, which enables bi-directional communication with the external microcontroller.

The ST25R3910 also features the Automatic Antenna Tuning (AAT) technology, enabling the reader to re tune itself to deliver maximum output at 13.56 MHz, when the surroundings detune the antenna.

Key Features

  • Close loop adjustment of ASK modulation for accurate control of modulation depth in case of ISO-14443B protocol
  • Low power (3.5 μA) NFC target mode
  • AM/PM demodulator
  • Accurate RF envelope measurement (8-bit A/D converter)
  • High output power at 3.3 V power supply:
    • Up to 700 mW in case regulator is externally shorted
    • Up to 500 mW in case of differential output when antenna trimming is used
    • Up to 125 mW in case of single ended output when antenna trimming is used
  • Squelch for gain reduction, to compensate for noise generated by tag processing
  • Automatic Antenna tuning (AAT)
  • Transparent mode
  • Amplitude and phase measurement
  • Supporting 13.56 MHz and 27.12 MHz quartz oscillator with fast start-up
  • Supply voltage range from 2.4 to 3.6 V
  • Wide temperature range: -40 ºC to 85 ºC
  • Package: 32-pin QFN (5x5mm)
Product Specifications
DescriptionVersionSize
DS11844: Mid-range HF reader with 0.7 W supporting AAT1.01 MB
Flyers
DescriptionVersionSize
High performance NFC/RFID readers1.0981 KB
Sample & Buy
Part NumberPackagePacking TypeUnit Price (US$) *QuantityECCN (EU)ECCN (US)Country of Origin
ST25R3910-BQFMVFQFPN 32 5x5x1.0Tape And Reel--NECEAR99-
ST25R3910-BQFTVFQFPN 32 5x5x1.0Tape And Reel2.51000NECEAR99-
Quality & Reliability
Part NumberPackageGradeRoHS Compliance GradeMaterial Declaration**
ST25R3910-BQFMVFQFPN 32 5x5x1.0IndustrialN/A
ST25R3910-BQFTVFQFPN 32 5x5x1.0IndustrialN/A
Mid-range HF reader with 0.7 W supporting AAT ST25R3910
Mid-range HF reader with 0.7 W supporting AAT ST25R3910